Ideal Vacuum Cube Replacement Viton O-ring for Sealing 15 x 15 in. Octagonal Top or Bottom Plate. These replacement Viton O-rings are used on all top and bottom octagonal plates that fit our 15 x 15 x 6 in. octagonal Ideal Vacuum Cube modular chambers. They are are used to create a vacuum tight seal between the octagonal frame and plate. These o-ring seals are installed on the inner sealing groove of the plate. They are made of Viton and can be baked up to 150 degrees Celsius without permanent deformation. Chambers sealed with Viton O-rings can achieve vacuum in the 10-8 Torr range (high vacuum).

O-Ring Removal Tool, Non Scratch Polycarbonate, Keeps O-Ring Seals and Grooves from Damage This O-ring removal tool, made of non scratch, tough polycarbonate plastic, allows you to remove O-rings from the groove without damaging either the O-ring seal or the groove. This 5-1/2" long, nearly unbreakable tool has a prying tip on one end, and a hook on the other which allows you to remove even the most stubborn O-rings, even in hard-to-reach places. This tool is a must have in your toolbox! We recommended it for installation, maintenance and service on the Ideal Vacuum Cube modular chamber system, or with any vacuum component. Note: Color may vary.

Ideal Vacuum Cube Viewing Window Assembly Maintenance and Service Tool Kit This simple toolkit includes a 9/64" hex key wrench and an O-ring removal tool. It is a perfect little tool kit for maintaining and servicing ALL Ideal Vacuum Cube Viewing Window Assemblies; 6x6, 6x12, 9x9 and 12x12. Use it when disassembling the standard glass for cleaning, for periodic tightening, when replacing the O-ring window pane seal, or when replacing the standard tempered glass with fused quartz or fused silica material. This is a simple yet essential tool kit for maintaining and servicing the Ideal Vacuum Cube Viewing Window Assembly. Please see our other tool kits for a Cube plate mounting tool kit, or for our complete Cube maintenance and service tool kit which has all the tools needed for proper Cube assembly, disassembly, maintenance and repair.

Ideal Vacuum Cube Plate Maintenance and Service Tool Kit This simple and inexpensive toolkit includes a 3/16" hex key wrench and an O-ring removal tool. It is a perfect little tool kit for installing, maintaining and servicing ALL Ideal Vacuum Cube side or door plates, whether they be ported or not. Use these essential tools when mounting sides to the Cube, or when replacing O-ring seals. These tools work for all 6x6, 6x12, 9x9 and 12x12 Cubes; rectangular, hexagonal or octagonal chambers. Please see our other tool kits for a complete essential Cube maintenance and service tool kit, which has all the tools needed for proper Cube assembly, disassembly, maintenance and repair.

Ideal Vacuum Cube Essential Maintenance and Service Tool Kit This tool kit has everything you need to assemble, disassemble, maintain, service and repair all Ideal Vacuum Cube modular chambers. Includes: 13 pc. Hex key wrench set (inch sizes from 0.050" to 3/8", U.S.A) 7/16" polished combination wrench (for Cube coupling) O-Ring Removal Tool (non scratch polycarbonate, for all O-ring seals) 2 pair of Large Nitrile gloves (use when working on any vacuum component) We’ve gathered all the essential tools you need and packaged them in their own snap close polypropylene box that fits comfortably in your vacuum service tool box, or a desk drawer. Use these essential tools when assembling or installing a Cube for the first time, or when performing routine maintenance, cleaning, and seal replacement. These tools work for all 6x6, 6x12, 9x9 and 12x12 Cubes; rectangular, hexagonal or octagonal chambers, and all accessories that use hex head bolts or screws for attachment to the Cube system (valves, flanges, etc.). This inexpensive tool kit is a must have for all Ideal Vacuum Cube modular chamber system users. Dimensions: 8-3/8" x 3-5/8" x 2". Color may vary.

Ideal Vacuum Cube Hardware Kit For 6 x 12 x 12 Chamber, Includes O-rings And Plate Mounting Screws. This Ideal Vacuum Cube hardware kit is needed when constructing a 6 x 12 x 12 chamber. The 6 x 12 x 12 Cube frame takes four 6" x 12" and two 12" x 12" plates to complete it (P108364). This kit includes O-rings for all the plates and the 1/4"-20 x 5/16" long stainless steel socket head cap screws (SHCS) needed to mount the plates on the frame. O-rings are made of Viton and can be baked up to 150 degrees Celsius. The socket head cap screws (SHCS) are made of 18-8 stainless steel. This kit also includes a complete spare set of four 6" x 12" and two 12" x 12" Cube plate O-rings, and 16 spare plate mounting screws. This 6 x 12 x 12 Cube hardware kit includes: (8 ea) Viton O-ring for 6 x 12 Cube Plate, P108339 (includes 4 spares) (4 ea) Viton O-ring for 12 x 12 Cube Plate, P108428 (includes 2 spares) (96 ea) 1/4"-20 x 5/16" long SHCS screws for plate mounting, P1013341 (includes 16 spares) Please download the Cube plate installation manual for installation instructions. Use the Cube plate maintenance and service toolkit (P1010554) to assemble a Cube.

Ideal Vacuum Cube Hardware Kit For 6 x 6 x 6 Hexagonal Chamber, Includes O-rings And Plate Mounting Screws. This Ideal Vacuum Cube hardware kit is needed when constructing a 6 x 6 x 6 hexagonal chamber. The 6 x 6 x 6 hexagonal Cube frame takes eight 6" x 6" plates to complete it (P108699). This kit includes O-rings for all the 6 x 6" plates and the 1/4"-20 x 5/16" long stainless steel socket head cap screws (SHCS) needed to mount the plates on the frame. O-rings are made of Viton and can be baked up to 150 degrees Celsius. The socket head cap screws (SHCS) are made of 18-8 stainless steel. This kit also includes a complete spare set of eight 6" x 6" Cube plate O-rings and 8 spare plate mounting screws. This 6 x 6 x 6 hexagonal Cube hardware kit includes: (16 ea) Viton O-ring for 6 x 6 Cube Plate, P107295 (includes 8 spares) (72 ea) 1/4"-20 x 5/16" long SHCS screws for plate mounting, P1013341 (includes 8 spares) Please download the Cube plate installation manual for installation instructions. Use the Cube plate maintenance and service toolkit (P1010554) to assemble a Cube.

Ideal Vacuum Cube Hardware Kit For 6 x 6 x 12 Hexagonal Chamber, Includes O-rings And Plate Mounting Screws. This Ideal Vacuum Cube hardware kit is needed when constructing a 6 x 6 x 12 hexagonal chamber. The 6 x 6 x 12 hexagonal Cube frame takes six 6" x 12" and two 6" x 6" plates to complete it (P108697). This kit includes O-rings for all the plates and the 1/4"-20 x 5/16" long stainless steel socket head cap screws (SHCS) needed to mount the plates on the frame. O-rings are made of Viton and can be baked up to 150 degrees Celsius. The socket head cap screws (SHCS) are made of 18-8 stainless steel. This kit also includes a complete spare set of six 6" x 12" and two 6" x 6" Cube plate O-rings, and 12 spare plate mounting screws. This 6 x 6 x 12 hexagonal Cube hardware kit includes: (12 ea) Viton O-ring for 6 x 12 Cube Plate, P108339 (includes 6 spares) (4 ea) Viton O-ring for 6 x 6 Cube Plate, P107295 (includes 2 spares) (100 ea) 1/4"-20 x 5/16" long SHCS screws for plate mounting, P1013341 (includes 12 spares) Please download the Cube plate installation manual for installation instructions. Use the Cube plate maintenance and service toolkit (P1010554) to assemble a Cube.

Ideal Vacuum Cube Hardware Kit For 24 x 24 x 24 Chamber, Includes O-rings And Plate Mounting Screws. This Ideal Vacuum Cube hardware kit is needed when constructing a 24 x 24 x 24 chamber. The 24 x 24 x 24 Cube welded stainless steel frame with door takes twenty 12 x 12" plates to complete it (P108734). This kit includes O-rings for all the 12 x 12 plates and the 1/4"-20 x 5/16" long stainless steel, plate socket head cap screws (SHCS) needed to mount the plates on the frame. O-rings are made of Viton and can be baked up to 150 degrees Celsius. The socket head cap screws (SHCS) are made of 18-8 stainless steel. This kit also includes a complete spare set of twenty 12" x 12" Cube plate O-rings and 16 spare plate mounting screws. This 24 x 24 x 24 Cube hardware kit includes: (40 ea) Viton O-ring for 12x12 Cube Plate, P108428 (includes 20 spares) (336 ea) 1/4"-20 x 5/16" long SHCS screws for Plate Mounting, P1013341 (includes 16 spares) Please download the Cube plate installation manual for installation instructions. Use the Cube plate maintenance and service toolkit (P1010554) to assemble a Cube.

Ideal Vacuum Cube Hardware Kit For 15 x 15 x 6 Octagonal Chamber, Includes O-rings And Plate Mounting Screws. This Ideal Vacuum Cube hardware kit is needed when constructing a 15 x 15 x 6 octagonal chamber. The 15 x 15 x 6 octagonal Cube frame takes eight 6" x 6" and two 15" x 15" top and bottom plates to complete it (P108700). This kit includes O-rings for all the plates, including octagonal adapter plates, and the 1/4"-20 x 5/16" long stainless steel socket head cap screws (SHCS) needed to mount the plates on the frame, including screws for top and bottom adapter plates. O-rings are made of Viton and can be baked up to 150 degrees Celsius. The socket head cap screws (SHCS) are made of 18-8 stainless steel. The top and bottom 15 in. octagonal plates may be blank (P1013090), or be adapter plates that accept a 6 x 6 plate (P1013088), a 9 x 9 plate (P1013043), or a 6 x 12 plate (P1013089). This kit includes spare 6" x 6" O-rings, spare 9" x 9" (also fits 6 x 12") O-rings, and spare 15" x 15" plate O-rings to seal the top and bottom plates. It also includes spare screws. This 15 x 15 x 6 octagonal Cube hardware kit includes: (20 ea) Viton O-ring for 6 x 6 Cube Plate, P107295 (includes 10 spares) (4 ea) Viton O-ring for 9 x 9 or 6 x 12 Cube Plate, P108339 (includes 2 spares) (4 ea) Viton O-ring for 15 x 15 octagonal top/bottom Cube Plate, P1013173 (includes 2 spares) (132 ea) 1/4"-20 x 5/16" long SHCS screws for plate mounting, P1013341 (includes 12 spares) Please download the Cube plate installation manual for installation instructions. Use the Cube plate maintenance and service toolkit (P1010554) to assemble a Cube.

1/4-20 x 5/16 in. Socket Head Cap Screws (SHCS), 1/4-20 Thread Size by 5/16 in. Long, 304 Stainless Steel 1 Each. Used to mount all Ideal Vacuum Cube Plates. These 1/4-20 x 5/16-inch socket head cap screws (SHCS) have a diameter of 1/4 inch, with 20 threads per inch, and are 5/16 inch long. They are non-magnetic being made of chemical and corrosion resistant 304 stainless steel. Socket head cap screws have a smaller head diameter than normal screws. They are tightened using an Allen wrench (hex key) which is inserted into the recessed hex-drive socket located in the screw head. The screw length is measured from under the head (length of shaft only) and are sold as 1 each. These 1/4-20 x 5/16 long hex screws are used on all Ideal Vacuum Cube plates. Buy a few as spares in case one gets lost or boogered up. 1/4-20 x 5/16-inch socket head cap screws (SHCS) Product details: Head style: Socket cap Drive type: Allen Material: Stainless steel Grade: 304 Stainless steel (chemical resistant) Diameter: 1/4 inch Thread count: 20 TPI Length: 5/16 inch Thread direction: Right hand Drive size: 3/16" Units: US We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 1/4" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 1/4" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 1/4" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 5/16" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 5/16" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 5/16" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 3/8" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 3/8" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 3/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 1/2" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 1/2" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 1/2" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 5/8" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 5/8" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 5/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 3/4" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 3/4" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 3/4" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 7/8" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 7/8" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 7/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

1/4-20 x 1" Vacuum Vented Socket Head Cap Screws, 1/4-20 Thread Size by 1" Long, 304 Stainless Steel, Sold as Each. These 1/4-20 x 1" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 5/16" Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 5/16" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 5/16" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 3/8" Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 3/8" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 3/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 1/2 Inch Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 1/2" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 1/2" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 3/4 Inch Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 3/4" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 3/4" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 7/8 Inch Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 7/8" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 7/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 1 Inch Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 1" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 1" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

8-32 x 5/8 Inch Vacuum Vented Socket Head Cap Screws, 8-32 Thread Size by 5/8" Long, 304 Stainless Steel, Sold as Each. These 8-32 x 5/8" long vacuum vented socket head cap screws (SHCS) are drilled through the head and shaft to vent fluid and gases trapped below the screw, making them necessary for vacuum applications. These vented scews are sold by the piece (1 each). When used as vacuum fasteners inside a vacuum chamber, typical solid shaft (unvented) screws trap gases in the void space between the screw tip and the bottom of the threaded hole. These trapped gases are slowly released into the evacuated chamber thus creating what is known as a virtual leak. Virtual leaks slow down pumping processes and can significantly prolong the time needed to reach the desired base pressure. These vented screws, also known as vacuum screws, help eliminate virtual leaks from high vacuum (HV) and ultra-high (UHV) systems. Our vacuum compatible vented screw fasteners have been drilled through the entire length of their shaft allowing these trapped gases to vent out. These screws are non-magnetic and made of chemical and corrosion resistant 304 stainless steel. The screw length is measured from under the head (length of shaft only). We know that selecting the correct vacuum hardware for your vacuum system can seem like a challenging process. To make buying easier we sell the hardware individually by the bolt specifications (bolt diameter, thread type, and length), or in prepackaged hardware sets tailored for specific applications, such as for connecting ISO, CF (Conflat), or ASA flanges, or for connecting vacuum valves. Links to bolt sets for some selected applications: Bolt Sets For ASA Vacuum Flanges Bolt Sets For Conflat (CF) Vacuum Flanges Bolt Sets For ISO-F (ISO LFB) Vacuum Flanges Bolt Sets For Vacuum Valves Bolt Sets For Ideal Vacuum Cubes Please send us an email if you are looking to order large quantities of fasteners or other hardware. We can offer substantial discounts for bulk orders. If you cannot find the particular hardware you need, please send us an email and we will quote it for you: fasteners@idealvac.com

Bolt Kit For 1.33 In. Conflat Tapped Bolt Hole Flanges, Silver-Plated Allen Bolts With Washers.These bolt kits contain silver-plated Allen head bolts and washers to fasten tapped hole 1.33 (1-1/3) inch CF Conflat flanged fittings. These confalt flages can be pumped down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2-1/8, 2-3/4, 4-1/2, 4-5/8, 6, 6-3/4, 8, 10, 12, 13-1/4, 14 and 16-1/2. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250.Complete Kit - 1.33 (1-1/3) inch Conflat Tapped Bolt Hole Fasteners: QTY 6, Silver-Plated 8-32 x 0.50 Inch Long Allen Bolts QTY 6, Washers

Bolt Kit For 2.75 (2-3/4) In. Conflat Tapped Bolt Hole Flanges, Silver-Plated Allen Bolts With Washers.These bolt kits contain silver-plated 12-Point head bolts and washers to fasten tapped hole 2.75 (2-3/4) inch CF Conflat flanged fittings. These confalt flages can be pumped down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2-1/8, 2-3/4, 4-1/2, 4-5/8, 6, 6-3/4, 8, 10, 12, 13-1/4, 14 and 16-1/2. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250.Complete Kit - 2.75 (2-3/4) inch Conflat Tapped Bolt Hole Fasteners: QTY 6, Silver-Plated 1/4-28 x 0.875 Inch Long 12-Point Head Bolts QTY 6, Washers

Bolt Kit for Ideal Vacuum Cube Plates with CF 3.375" or 4.5" Conflat Port, Eight Silver-Plated, 12-Point Bolts With Washers, 5/16-24 x 1.0". This hardware kit is specifically for Ideal Vacuum Cube plates that have a Conflat 3.375" or 4.5" port with tapped bolt threads. The kit consists of eight (8) silver-plated, 12-point bolts, 5/16-24 x 1.0", and eight (8) stainless steel washers. The 1.0" screws are slightly shorter than the bolts typically used to connect two CF flanges together. The silver-plating on the bolts keeps them from galling and makes them easily removed and replaced when changing vacuum plumbing configurations. This kit consists of: 8 ea. silver-plated, 12 point, 5/16-24 x 1.0" bolts 8 ea. 304 stainless steel washers

Bolt Kit for Ideal Vacuum Cube Plates with CF 6.0" Conflat Port, Sixteen Silver-Plated, 12-Point Bolts With Washers, 5/16-24 x 1.0". This hardware kit is specifically for Ideal Vacuum Cube plates that have a Conflat 6.0" port with tapped bolt threads. The kit consists of sixteen (16) silver-plated, 12-point bolts, 5/16-24 x 1.0", and sixteen (16) stainless steel washers. The 1.0" screws are slightly shorter than the bolts typically used to connect two CF flanges together. The silver-plating on the bolts keeps them from galling and makes them easily removed and replaced when changing vacuum plumbing configurations. This kit consists of: 16 ea. silver-plated, 12 point, 5/16-24 x 1.0" bolts 16 ea. 304 stainless steel washers

Bolt Kit for Ideal Vacuum Cube Plates with CF 8.0" Conflat Port, Twenty Silver-Plated, 12-Point Bolts With Washers, 5/16-24 x 1.0". This hardware kit is specifically for Ideal Vacuum Cube plates that have a Conflat 8.0" port with tapped bolt threads. The kit consists of twenty (20) silver-plated, 12-point bolts, 5/16-24 x 1.0", and twenty (20) stainless steel washers. The 1.0" screws are slightly shorter than the bolts typically used to connect two CF flanges together. The silver-plating on the bolts keeps them from galling and makes them easily removed and replaced when changing vacuum plumbing configurations. This kit consists of: 20 ea. silver-plated, 12 point, 5/16-24 x 1.0" bolts 20 ea. 304 stainless steel washers

Bolt Kit for Ideal Vacuum Cube Plates with CF 10.0" Conflat Port, Twenty-Four Silver-Plated, 12-Point Bolts With Washers, 5/16-24 x 1.0". This hardware kit is specifically for Ideal Vacuum Cube plates that have a Conflat 10.0" port with tapped bolt threads. The kit consists of twenty-four (24) silver-plated, 12-point bolts, 5/16-24 x 1.0", and twenty-four (24) stainless steel washers. The 1.0" screws are slightly shorter than the bolts typically used to connect two CF flanges together. The silver-plating on the bolts keeps them from galling and makes them easily removed and replaced when changing vacuum plumbing configurations. This kit consists of: 20 ea. silver-plated, 12 point, 5/16-24 x 1.0" bolts 20 ea. 304 stainless steel washers

Ideal Vacuum Cube Cooling Plate Adapter Kit Connects Two Thermal Fluid 12x12 Plates to One Chiller. This cooling plate adapter kit is used to connect two Ideal Vacuum Cube 12x12 cooling plates (P108474) to one Thermo Scientific Neslab model Arctic, AC200 A25, AC200 A40, or Accel 500LT cooler. The kit branches the main cooling line off to a secondary cooling plate attached to a second 12x12 Ideal Vacuum Cube, allowing both chambers to be chilled in conjunction with one single chiller. This cooling plate adapter kit comes with: 5ft length of 1/2" ID insulated hose (x2) 3/8" x 1/2" OD tube adapters (x2) 1/2" x 1/2" x 1/2" OD Stainless Steel Barbed Tee (x2) #10 Stainless Steel Clamps (x4)