NEW Varian Agilent XGS-600 Multi-Gauge Controller - Basic Controller, no add on cards. PN XGS600H0M0C0 Accepts any and up to 6 of the FOUR gauge cards: (Controller Dual Analog Input Card) (ConvecTorr Convection Gauges/Thermocouple Gauge Card) (Hot-Filament Ion Gauges (HFIG) Card) (Inverted-Magnetron (IMG) Cold-Cathode or Penning Gauge Card) The XGS-600 Vacuum Gauge Controller provides unprecedented capacity, performance and flexibility in a cost effective, standard half-rack package. A programmable dot matrix LCD provides display flexibility, and simple screen organization and navigation makes the unit extremely easy to use. Drop down gauge selection automatically sets the emission current, sensitivity and overpressure. The screen displays up to eight gauges and pressures simultaneously, and permits the user to label each gauge. 8 set points, fully programmable RS232/RS485 serial communications and universal voltage compatibility are standard on all units. A large-font feature provides visibility from up to 20 feet. Expansion or re-configuration in the field is easy to do with PCB Cards available on this website. Controllers without cards (can accept up to 4 cards) and may issue set point commands through computer interface only. This XGS-600 can only fit up to 5 cold cathode (IMG Gauges) or 4 Hot Ion Gauges from slots 1-4. (With restrictions, refer to Sensor Card Installation.) The XGS-600 replaces both MultiGauge and SenTorr rack mount controllers. While the XGS-600 was designed to be substantially backwards compatible, there are some design features that prevent the new product from being 100% backwards compatible. (See page A-9 in the XGS-600 Instruction Manual for compatibility limitations.) The XGS-600 is also compatible with other competitor gagues, (See Instruction Manual page 2-4 for Cross Reference) PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG Boards are long high profile cards and can only be installed in slots 1-4. Options Slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet and the Vacuum Measurement Brochure Page 11) by scrolling down to AVAILABLE DOWNLOADS) For Complete Specs, Users Manual and Replacement Card Instructions, see .pdf's below under (AVAILABLE DOWNLOADS)

NEW Varian Agilent XGS-600 Multi Gauge Vacuum Controller - Basic Controller, with ONE Dual Analog Input Card installed able to control two active gauges, PN XGS600H0M0C0A1. Accepts any and up to 6 of the FOUR gauge cards: (Controller Dual Analog Input Card) (ConvecTorr Convection Gauges/Thermocouple Gauge Card) (Hot-Filament Ion Gauges (HFIG) Card) (Inverted-Magnetron (IMG) Cold-Cathode or Penning Gauge Card) The XGS-600 Vacuum Gauge Controller provides unprecedented capacity, performance and flexibility in a cost effective, standard half-rack package. A programmable dot matrix LCD provides display flexibility, and simple screen organization and navigation makes the unit extremely easy to use. Drop down gauge selection automatically sets the emission current, sensitivity and overpressure. The screen displays up to eight gauges and pressures simultaneously, and permits the user to label each gauge. 8 set points, fully programmable RS232/RS485 serial communications and universal voltage compatibility are standard on all units. A large-font feature provides visibility from up to 20 feet. Expansion or re-configuration in the field is easy to do with PCB Cards available on this website. Controllers without cards (can accept up to 4 cards) and may issue set point commands through computer interface only. This XGS-600 can only fit up to 5 cold cathode (IMG Gauges) or 4 Hot Ion Gauges from slots 1-4. (With restrictions, refer to Sensor Card Installation.) The XGS-600 replaces both MultiGauge and SenTorr rack mount controllers. While the XGS-600 was designed to be substantially backwards compatible, there are some design features that prevent the new product from being 100% backwards compatible. (See page A-9 in the XGS-600 Instruction Manual for compatibility limitations.) The XGS-600 is also compatible with other competitor gauges, (See Instruction Manual page 2-4 for Cross Reference) PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG Boards are long high profile cards and can only be installed in slots 1-4. Option Slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet and the Vacuum Measurement Brochure Page 11) by scrolling down to AVAILABLE DOWNLOADS) For Complete Specs, Users Manual and Replacement Card Instructions, see .pdf's below under (AVAILABLE DOWNLOADS)

NEW Varian Agilent Technologies XGS-600, XGS600, XGS 600, Vacuum Gauge Controller with HFIG Hot Filament Ion Gauge Card PN: XGS600H1M0C0 The XGS-600 Vacuum Gauge Controller provides unprecedented capacity, performance and flexibility in a cost effective, standard half-rack package. A programmable dot matrix LCD provides display flexibility, and simple screen organization and navigation makes the unit extremely easy to use. Drop down gauge selection automatically sets the emission current, sensitivity and overpressure. The screen displays up to eight gauges and pressures simultaneously, and permits the user to label each gauge. 8 set points, fully programmable RS232/RS485 serial communications and universal voltage compatibility are standard on all units. A large-font feature provides visibility from up to 20 feet. This XGS-600 is outfitted with the Hot Filament Ion Gauge HFIG board which operates all Varian hot filament gauges and most other available Bayard-Alpert type hot filament ionization gauges including nude UHV types. The board can be set up for all Varian hot filament gauges and allows you to set gauge emission current, sensitivity value, and gas correction factor. The UHV range and E-Beam degas are standard, as is dual filament control, remote I/O control of emission and filament selection, and 0 to 10 V analog output. Other cards can also be used along side this Dual Convection Card. The HFIG board is compatible with the following gauges in the high to ultra high vacuum range from 10-3 to 10-10 Torr: 563 (HV) 564 (HV) 571 (HV) 572 (HV) MBA-100, MBA-200 (HV) UHV-24, UHV-24p (UHV) Also compatible with competitor's gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference.) The XGS-600 Controller accepts any, and up to 6, of the available FOUR gauge cards: (Controller Dual Analog Input Card) (ConvecTorr Convection Gauges/Thermocouple Gauge Card) (Hot-Filament Ion Gauges (HFIG) Card) (Inverted-Magnetron (IMG) Cold-Cathode or Penning Gauge Card) Expansion or re-configuration in the field is easy to do with PCB Cards available on this website. The XGS-600 replaces both MultiGauge and SenTorr rack mount controllers. While the XGS-600 was designed to be substantially backwards compatible, there are some design features that prevent the new product from being 100% backwards compatible. (See page A-9 in the XGS-600 Instruction Manual for compatibility limitations.) For more detailed information including Specifications, Users Manual and Replacement Card Instructions, please see the available .PDF's.

NEW Varian Agilent Dual Analog Input Card for the XGS-600 Multi-Gauge Controller, Agilent Varian Part Number R3487301. This is a Dual Analog Input Card for the XGS-600 Multi-Gauge Controller. Depending on the XGS-600 Controller configuration it may or may not have this Dual Analog Input Card. With 1 Analog Input Card the XGS-600 Controller can read 2 active gauges (2 active gauges per card). Up to 6 Dual Analog Input Cards can be installed in the XGS-600 Controller, for a total of 12 active gauge inputs. Other cards can also be used along side this Dual Analog Input Card. Agilent Varian Part Number R3487301. Compatible with the following Varian Agilent active gauges: CT-100, PVG-500, Rough Vacuum Atm to 10-3 CDG-500, PCG-750, High Vacuum 10-3 to 10-9 FRG-700, FRG-720/730, High Vacuum 10-3 to 10-9 This is the Dual Analog Input Card ONLY. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG Boards are long high profile cards and can only be installed in slots 1-4. Option Slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

NEW Varian Agilent Dual Convection Thermocouple Gauge Card for the XGS-600 Multi-Gauge Vacuum Controller, Agilent Varian Part Number R3084301 This is the Dual Convection Gauge Card for the XGS-600 Mulit-Gauge Vacuum Controller. The Convection card operates 2 thermocouple or 2 convection gauges and allows you to calibrate to the actual atmospheric pressure value, to vacuum pressure and select calibration of air or argon. Each channel has its own 9 pin Dsub connector. Other cards can also be used along side this Dual Convection Card. Compatible with the following gauges in the rough vacuum range from atmosphere to 10-3: ConvecTorr 536 531 Also compatible with competitors gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference below.) This is the Dual Convection Thermocouple Gauge Card ONLY. For Complete Board Specifications/Descriptions see XGS-600 Instruction/Users Manual .pdf page A-3 below. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600 controller. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG boards are long high profile cards and can only be installed in slots 1-4 Option slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

NEW Varian Agilent Hot Filament Ion Gauge (HFIG) Card for the XGS-600 Multi-Gauge Vacuum Controller, Agilent Varian Part Number R3075301 This is the Hot Filament Ion Gauge HFIG board and operates all Varian hot filament gauges and most other available Bayard-Alpert type hot filament ionization gauges including nude UHV types. The board can be set up for all Varian hot filament gauges and allows you to set gauge emission current, sensitivity value, and gas correction factor. The UHV range and E-Beam degas are standard, as is dual filament control, remote I/O control of emission and filament selection, and 0 to 10 V analog output. Other cards can also be used along side this Dual Convection Card. Compatible with the following gauges in the high to ultra high vacuum range from 10-3 to 10-10: 563 (HV) 564 (HV) 571 (HV) 572 (HV) MBA-100, MBA-200 (HV) UHV-24, UHV-24p (UHV) Also compatible with competitors gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference below.) This is the Hot Filament Ion Gauge (HFIG) ONLY. For Complete Board Specifications/Descriptions see XGS-600 Instruction/Users Manual .pdf page A-3 below. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600 controller. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG boards are long high profile cards and can only be installed in slots 1-4 Option slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

Agilent Varian Inverted Magnetron Ion Gauge (IMG) for XGS-600 Multi-Gauge Vacuum Controller, Agilent Varian Part Number R3080301This is the Agilent Varian (IMG) Inverted Magnetron Board and operates the Ultra High Vacuum IMG-100 and IMG-300 gagues. It allows you to set the gauge sensitivity value, and gas correction factor. The (UHV) Ultra High Vacuum range is standard, as is remote I/O control of emmission and 0 to 10 V analog output.Compatible with the following gauges in the ultra high vacuum range from 10-9 to 10-10: IMG-100, IMG-300 (UHV) Also compatible with competitors gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference below.) This is the Inverted Magnetron Ion Gauge (IMG) ONLY. For Complete Board Specifications/Descriptions see XGS-600 Instruction/Users Manual .pdf page A-3 below. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600 controller.Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG boards are long high profile cards and can only be installed in slots 1-4 Option slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf’s (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

Agilent Signal Cable for XGS-600, or SennTorr Gauge Controller to Thermocouple Sensor, 10 foot length. Agilent Varian Part Number: L91313010. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian Thermocouple Sensor Transducers. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Signal Cable for XGS-600, or SennTorr Gauge Controller to Thermocouple Sensor, 30 foot length. Agilent Part Number: L91313030. This is a Agilent Varian 30 ft. signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to Agilent Varian Thermocouple Sensor Transducers.Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Signal Cable for XGS-600, or SennTorr Gauge Controller to Thermocouple Sensor, 50 foot length. Agilent Varian Part Number: L91313050. This is a Agilent Varian signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Agilent Varian ConvecTorr Sensors. Cable 50 foot cable length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian ConvecTorr Sensor CABLE. Signal cable, standard 10 foot length, L91223010 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian ConvecTorr Sensor Transducers. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian 25 Foot Cable connects XGS-600XGS SenTorr Gauge Controller to ConvecTorr Sensor. Signal cable, 50 foot length. Agilent Varian Part Number L91223025 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Varian ConvecTorr Sensors. Cable 25 foot cable length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian 50 Foot Cable connects XGS-600XGS SenTorr Gauge Controller to ConvecTorr Sensor. Signal cable, 50 foot length. Agilent Varian Part Number L91313050. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Varian ConvecTorr Sensors. Cable 50 foot cable length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian IMG100 or IMG300 Inverted Magnetron Gauge Sensor Tube CABLE. Signal cable, standard 10 foot length, Non-bakeable. R03113010 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian IMG100 or IMG300 Inverted Magnetron Gauge Sensor CABLE. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian IMG300 Inverted Magnetron Gauge Sensor or IMG-UHV gauge sensor, CABLE. Signal cable, standard 10 foot length, Bakeable. R03413010 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian IMG300 Inverted Magnetron Gauge or IMG-UHV inverted magnetron gauge, CABLE. Bakeable. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian Inc. UHV-24 or UHV-24p Sensor Tube Cable. standard 10 foot length, bakeable to 250 C. (Varian Agilent INC. Only) R32463010 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian UHV-24 or UHV-24p nude ion gauge tube. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian Sensor Tube Cable, 25 foot, XGS-600, Multi-Gauge, SenTorr Gauge Controller to Nude Ion Gauge Agilent Varian Part Number: R32453025 This is a Varian Agilent cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian UHV-24 or UHV-24p nude ion gauge tube. Cable standard 25 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian Cable Assembly, 50 feet for PVG-500 Active Pirani Gaugem, FRG-700 Pirani/IMG to GXS-600 Vacuum Gauge Controller with Open Active Port Cable. PN: R35893050 This is a Varian Agilent cable which hooks up to the XGS-600 Controller or Active Gauge Controller to the PVG-500 Pirani Gauge or FRG-700 Pirani/IMG gauge. This is the cable only 50 ft. length all gauges and controllers sold separately on this website. Agilent Varian Part Number R35893050. Can be used with the following Varian Controllers: XGS-600 Controller Active Gauge Controller ACG-100, AGD-100

Newest-Style Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 10 ft. (New Style) Works With Newest-Style XGS-600 Hot Cathode Gauge Cards - New cable PN: X3203-60006 These Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest style MBA 2-200T to hot cathode gauge controller (HFIG) card for XGS-600 controller and have Agilent Varian part number X3203-60006. These are new and come with full Agilent Varian warranty. These new cables are for the newer versions of the MBA 2-200T dual filament full metal hot cathode ion gauge sensors to XGS 600 controller's only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors. Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Newest Style Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 25 ft. (New Style)Works With Newest-Style XGS-600 Hot Cathode Gauge Cards - New cable PN: X3203-60007 These Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest-style MBA 2-200T to hot cathode gauge controller (HFIG) cards for XGS-600 controller and have Agilent Varian part number X3203-60007. These are new and come with full Agilent Varian warranty. These new cables are for the newer versions of the MBA 2-200T dual filament full metal hot cathode ion gauge sensors to XGS 600 controller’s only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors. Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Newest Style Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 50 ft. (New Style)Works With Newest-Style XGS-600 Hot Cathode Gauge Cards - New cable PN: X3203-60008 These Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest-style MBA 2-200T to hot cathode gauge controller (HFIG) cards for XGS-600 controller and have Agilent Varian part number X3203-60008. These are new and come with full Agilent Varian warranty. These new cables are for the newer versions of the MBA 2-200T dual filament full metal hot cathode ion gauge sensors to XGS 600 controller’s only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors. Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Varian Agilent XGS-600, Multi-Gauge, and SenTorr Gauge Controller to standard Bayard-Alpert Gauge (Varian, Inc. models 563, 564, 571, or 572) Sensor Tube Cable, 10 foot length, non-bakeable, for glass ion gauge tube, non-bakeable. R32443010 This is a Varian Agilent signal cable and hooks up to the XGS-600, Multi-Gauge, and SenTorr Gauge Controller to the Varian Glass Ion Sensor Tubes, 563, 564, 571, 572. Cable standard 10 foot length. This is the cable only all gauges and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller Multi-Gauge Controller SenTorr Controller

Varian Agilent XGS-600, Multi-Gauge, and SenTorr Gauge Controller to standard Bayard-Alpert Gauge (Varian, Inc. R32443025 This is a Varian Agilent signal cable and hooks up to the XGS-600, Multi-Gauge, and SenTorr Gauge Controller to the Varian Glass Ion Sensor Tubes, 563, 564, 571, 572. Cable standard 25 foot length. This is the cable only all gauges and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller Multi-Gauge Controller SenTorr Controller

Varian Agilent XGS-600, Multi-Gauge, and SenTorr Gauge Controller to Nude Ion Gauge (Varian, Inc. models UHV-24 or UHV-24p) Sensor Tube Cable, 10 foot length, non-bakeable. PN R32453010 This is a Varian Agilent signal cable and hooks up to the XGS-600, Multi-Gauge, and SenTorr Gauge Controller to the Varian Glass Ion Sensor Tubes, UHV-24 or UHV-24p. Cable standard 10 foot length. This is the cable only all gauges and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller Multi-Gauge Controller SenTorr Controller

Varian FRG-720 Bayard Alpert, Pirani to GXS-600 Vacuum Gauge Controller, Active Port CABLE, 10 Foot Length. Agilent Varin Part Number R35913010. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller to the Varian FRG-720 Active Gauge Sensor Tube. Cable standard 10 foot length. This is the cable only all gauges and controllers sold separately on this website. Agilent Varin Part Number R35913010. Can be used with the following controller: Varian XGS-600

Agilent Varian PVG-500 Active Pirani Gauge and FRG-700 Pirani/IMG to GXS-600 Vacuum Gauge Controller CABLE with Open Active Ports, 10 Foot Length, Agilent Varian Part Number R35893010. This is a Varian Agilent signal cable and hooks up to the XGS-600 Controller or Active Gauge Controller to the PVG-500 Pirani Gauge or FRG-700 Pirani/IMG gauge. Standard 10 foot length. This is the cable only all gauges and controllers sold separately on this website. Agilent Varian Part Number R35893010. Can be used with the following Varian Controllers: XGS-600 Controller Active Gauge Controller ACG-100, AGD-100

Varian Agilent XGS-600 I/O Cable with Flying Leads, 10 foot Length. Agilent Varian Part Number R32493010. Varian Agilent XGS-600 I/O Cable with Flying Leads, 10 foot Length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following Varian Controllers: XGS-600 Controller

Varian Agilent XGS-600 I/O Cable with Flying Leads, 25 foot Length. Agilent Varian Part Number R32493025. Varian Agilent XGS-600 I/O Cable with Flying Leads, 25 foot Length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following Varian Controllers: XGS-600 Controller

Varian Agilent XGS-600 I/O Cable with Flying Leads, 50 foot Length. Varian Agilent Part Number R32493050. Varian Agilent XGS-600 I/O Cable with Flying Leads, 50 foot Length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following Varian Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Rack-Mounting Kit, 19 Inch, DUAL Mount, Side by Side, Optional Accessory, Agilent Varian Part Number L6426301. This is a Varian Agilent 19 inch rack mounting, DUAL Mount, Side by Side kit for the XGS-600 Multi-gauge Controller. This is the rack kit only all gauges, cables, and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Rack-Mounting Kit, 19 Inch, OFF Center, Optional Accessory, Agilent Varian Part Number L6422301. This is a Varian Agilent 19 inch rack mounting, OFF center kit for the XGS-600 Multi-gauge Controller. This is the rack kit only all gauges, cables, and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Rack-Mounting Kit, 19 Inch, ON Center, Optional Accessory, Agilent Varian Part Number L6423301. This is a Varian Agilent 19 inch rack mounting, ON center kit for the XGS-600 Multi-gauge Controller. This is the rack kit only all gauges, cables, and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Tilt Stand Accessory, Optional Accessory, Agilent Varian Part Number R3124301. This is a Varian Agilent XGS-600 Gauge Controller Tilt Stand Accessory, Optional Accessory. This is the Tilt Stand Only all gauges, cables, and vacuum controllers sold separately on this website. Agilent Varian Part Number R3124301. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Serial to USB Cable Connectivity Kit for IVP XG-120 and Other Controllers, Connects Serial RS232 to ComputerThis cable connectivity kit is needed for transferring data from an Ideal Vacuum XG-120 digital thermocouple gauge controller or any other controller with a serial output to a remote PLC or computer via RS232 serial communication, when the computer does not have a serial port. Most modern machines do not have a built in serial port, but do have a USB port. This kit consists of a 6 ft. Serial-to-USB cable and null modem adapter (controller sold separately). The cable’s DB9 male connector attaches through the null modem adapter onto the back of the controller, which has a DB9 female connector. The USB 2.0 type A connector plugs in to the computer’s USB port. Some controllers may have a DB25 serial interface in which case a DB25-to-DB9 adapter would be required. Controllers with serial interfaces include: IVP XG-120 Thermocouple Gauge Controller P108447, P108370 Agilent Varian RGC-150 Rough Thermocouple Gauge Controller, P105092 Agilent XGS-600 Vacuum Gauge Controller, P104122 Edwards Active Digital Pressure Controller, P107267 Edwards TIC Instrument Controller, P107177 Our serial-to-USB cable uses the FTDI chipset for ultimate compatibility with virtually all recent Windows, Mac and Linux platforms. Windows has built in drivers for the FTDI chipset. A variety of free, readily available, RS232 terminal software is available for online download, including PuTTY and TERMITE, which allows you to remotely monitor the output of vacuum pressure readings. Instructions for connecting and monitoring the XG-120 via RS232 serial communication are located here in the PDF downloads.