Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1/8 in. Male NPT Flange, 304L Stainless SteelPressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C, pn: L9090301 This is a Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1/8 in. Male NPT Flange, 304L Stainless Steel, Pressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool. Agilent Varian Part Number L9090301. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a separate gauge ONLY cables and controllers available on the website. A spec sheet, and other pertinent information is available for download in PDF format below.

Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1.33 in. CF Conflat Flange, 304L Stainless SteelPressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C, pn: L9090302 This is a Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1.33 in. CF Conflat Flange, 304L Stainless Steel, Pressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool. Agilent Varian Part Number L9090302. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a separate gauge ONLY cables and controllers available on the website. A spec sheet and other pertinent data is available for download in PDF format below.

Varian Agilent ConvecTorr Convection-Type Tube Sensor, KF16, NW16 Flange, 304L Stainless SteelPressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C, L9090305 This is a Varian Agilent ConvecTorr Convection-Type Tube Sensor, KF16, NW16 Flange, 304L Stainless Steel, Pressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool. Agilent Varian Part Number L9090305. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a separate gauge ONLY cables and controllers available on the website. A spec sheet and other pertinent date is available for download in PDF format below.

Varian Agilent ConvecTorr Convection-Type Tube Sensor, KF25, NW25 Flange, 304L Stainless Steel Pressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C, L9090306 This is a Varian Agilent ConvecTorr Convection-Type Tube Sensor, KF25, NW25 Flange, 304L Stainless Steel, Pressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool. Agilent Varian Part Number L9090306. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a separate gauge ONLY cables and controllers available on the website. A spec sheet and other pertinent data is available for download in PDF format below.

Varian Agilent ConvecTorr P Type Tube Sensor, 4 VCO Flange, SS, MSPLIB1918 Pressure Range: 1 × 10-4 torr to Atmosphere, Maximum bakeout temperature: 80 °C. This is a Varian Agilent ConvecTorr P-Type Tube Sensor, 4 VCO, 304L Stainless Steel, Pressure Range: 1 × 10-4 torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool. Agilent Varian Part Number MSPLIB1918. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a separate gauge ONLY cables and controllers available on the website. A spec sheet and other pertinent data is available for download in PDF format to the side.

Agilent Varian ConvecTorr Convection-PType Gauge Simulator and Reference Tube, Agilent pn: L7382301 Description: The Convectorr Simulator (L7382-301 P type) is intended to be a convenient tool for verifying proper operation of the MultiGauge, SennTorr or XGS-600 control units. For those cases when the target gauge tube can not be brought to proper pressure levels for true in-situ calibration, the simulator can be used to at least insure the control unit is calibrated to the average tube. Operation: Normally, the simulator would be plugged into the target gauge cable at the sensor end. When the switch is set to ATM the controller should read approximately 1 x 105 Pa (760 Torr, 1000mBar). If desired, the controller may be calibrated by pressing the (ATM) button on MultiGauge or the (CAL) button on SenTorr or CAL on main screen on the XGS-600. Sliding the switch to VAC should cause the controller to read approximately 1.33 x 10-1 Pa (1 mT, 1.3 x 10-3 mBar). Again, the controller may be calibrated by pressing the appropriate button on the controller keypad. NOTE: The Simulator is not intended to take the place of NIST-traceable calibration. The product is intended to verify the functionality of control electronics. For those situations requiring NIST-traceable calibration, Agilent Varian offers the comprehensive STARRS P Program. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a Separate ConvecTorr Gauge Simulator Only, Cables and Controllers available on this website.

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian ConvecTorr Sensor CABLE. Signal cable, standard 10 foot length, L91223010 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian ConvecTorr Sensor Transducers. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian 25 Foot Cable connects XGS-600XGS SenTorr Gauge Controller to ConvecTorr Sensor. Signal cable, 50 foot length. Agilent Varian Part Number L91223025 This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Varian ConvecTorr Sensors. Cable 25 foot cable length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian 50 Foot Cable connects XGS-600XGS SenTorr Gauge Controller to ConvecTorr Sensor. Signal cable, 50 foot length. Agilent Varian Part Number L91313050. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Varian ConvecTorr Sensors. Cable 50 foot cable length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

NEW Varian Agilent Dual Convection Thermocouple Gauge Card for the XGS-600 Multi-Gauge Vacuum Controller, Agilent Varian Part Number R3084301 This is the Dual Convection Gauge Card for the XGS-600 Mulit-Gauge Vacuum Controller. The Convection card operates 2 thermocouple or 2 convection gauges and allows you to calibrate to the actual atmospheric pressure value, to vacuum pressure and select calibration of air or argon. Each channel has its own 9 pin Dsub connector. Other cards can also be used along side this Dual Convection Card. Compatible with the following gauges in the rough vacuum range from atmosphere to 10-3: ConvecTorr 536 531 Also compatible with competitors gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference below.) This is the Dual Convection Thermocouple Gauge Card ONLY. For Complete Board Specifications/Descriptions see XGS-600 Instruction/Users Manual .pdf page A-3 below. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards : Slots are numbered left to right as viewed from the front of the XGS-600 controller. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG boards are long high profile cards and can only be installed in slots 1-4 Option slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf's (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

NEW Agilent Varian Scroll Pump Inverter Speed Control Kit, NW40. Agilent Varian Part Number X3814-68702 Replaces the old CT-100 PN: PTSCNTRLKIT2 These Varian CT-100 Active Rough Vacuum Transducers provides pressure measurements over a range of 1x10-4 Torr to atmosphere. The 0.2 second response time of the CT-100 and its excellent accuracy and precision allows its use in place of Pirani gauges. The CT-100 provides a stable analog voltage output as an indication of the test pressure and the unit can be calibrated in a selection of vacuum ranges. Two potentiometer-variable set points provide electrical alarms at selected pressures within the calibrated range of the device. Alarm indications are via the open collector grounding of two output transistors and the illumination of two LEDs. An internal power supply provides stable operating voltage from a wide range of external DC power sources. The gauge is contained in a plastic housing mounted by a 1/8 NPT vacuum fitting. The output pressure signal is a convenient 1 VDC to 9 VDC at 100 ohms internal impedance that can be used with strip chart recorders or other analog voltage data acquisition systems. A complete specifications, application and instruction manual can be downloaded in PDF format below. Need the ultimate in quiet operating vacuum pump equipment? Check out our Varian frequency controlled Inverter-Driven TriScroll 300 and 600 Dry Scroll vacuum pumps and our Varian HS452 and HS652 oil sealed rotary vane pumps. When the application reaches vacuum the pumps slow down and operates extremely quiet. This save electrical power (observed as low as 180 Watts where a normal fixed frequency pump uses 800 Watts) and allows the laboratory to be library quite for study and research. Added benefits are, frequency controlled pumps run cooler and contribute less heat into the laboratory and require less service because slower rotational speeds do not produce as much mechanical wear on the pump parts. We offer TriScroll 300 and 600 Inverter dry scroll and Varian HS452 and HS652 oil sealed rotary vane pumps which are sold on this website.